Runway Closure Marker RCM-D

Applications The Hali-Brite Runway Closure Marker is an effective and efficient method of warning pilots of closed runways and taxiways. A diesel engine powers 20 spotlights that form an illuminated “X” that can be seen as far as 25 miles. The trailer-mounted unit is easily towed behind a vehicle.

Runway Closure Marker RCM-D Specifications PDF

Features ETL certified to FAA AC 150/5345-55, AC 150/5370-2 and NTSB Safety Recommendation A-03-05 5-year, 5,000-hour engine warranty Easily set up by one person in two minutes, without tools Four folding arms each open to a 14-foot length 20 spotlights deliver over 144,000 candelas at beam center Visible 10-25 miles from runway under average conditions Selectable brightness levels to suit environmental conditions Photocell dimming for night operation Four rear-mounted lamps allow visual monitoring from back side Powered by a three-cylinder, liquid-cooled Mitsubishi diesel engine and Marathon brushless generator Operates 140 hours between fuel fills Highway tow-able, with a standard 2” hitch coupler 2200-pound, DOT-compliant trailer 3 swivel leveling jacks, one tongue jack Adjustable light beam angle Optional rear hitch, allows tandem towing of 2 units

Set Up Procedure (2 minutes):
		1. Level as necessary using 3 leveling jacks.
		2. Extend the 4 light assembly arms.
		3. Tilt the light to the upright position.
		4. Start the generator and activate the lights.

Runway Closure Marker Specifications

Light Assembly

Arm dimensions: 14 feet diagonal, 10 feet vertical
Front lamps: (20) 90 watt PAR38
Rear monitor lamps: (4) 90 watt PAR38
Lamp intensity: 140,000 center-beam candelas
Lamp visibility: Exceeds FAA specification of 5 nautical miles minimum at beam center. 1.5 nautical miles minimum for +/- 15 degrees azimuth and 0-10 degrees elevation
Lamp life: 6000 hours
Flash rate: 2.5 seconds on/2.5 seconds off
Flasher type: Solid-state zero-crossing switch
Flasher bypass: Automatic upon flasher failure
Frame: 4 inch x 4 inch aluminum tubing
Paint: Yellow epoxy powder-coat
Photocell: Dims lamps during night operation
Photocell override: Yes
Elevation angle: Adjustable 0-10 degrees
Set up time: 2 minutes
Operable w/o generator, 120 VAC

Warranty

Engine: 3 years or 3000 hours, plus 5 years or 5000 hours on major components
Generator:1 year unlimited hours, and 2 years or 2000 hours
Light Assembly: 1 year mechanical parts, 2 years electrical parts, excluding lamps

Engine

Manufacturer: Mitsubishi
Model: L3E-W261ML
Speed: 1800 RPM
Type: Diesel, 3-cylinder, liquid-cooled
Horsepower: 12.7 hp at 1800 RPM
Fuel Consumption: 0.41 gallons per hour
Start/Charging: Electric starter, alternator
Battery: 12V
Low Oil Shutdown
High Temp Shutdown
Engine Hour Meter
Glow Plug

Generator

Manufacturer: Marathon Electric
Type: 4-pole, brushless
Model: 332CSA5214
Output power: 6.0 kW
Power Factor: 1.0
Frequency: 60 Hz
Output voltage: 120/240V, single phase
Voltage regulation: +/- 5%
Output current: 50/25A

Chassis

2200 lb. axle
2-inch ball hitch
Three 2000 lb. leveling jacks
Side jack outriggers, 11-foot-6 inch span
DOT-compliant marker and tail lights
ST175/80D13 highway-rated tires
Safety chains with hooks
All steel tubing construction
Powder-coated steel engine housing
Lockable engine cabinet doors
External emergency engine stop
Removable trailer drawbar

AC Power Distribution

Main Breaker: 30A, 2-pole
120V Light Assembly Breaker: 30A, 2-pole
120V Outlet Breakers: 20A (2)
120V Twist-Loc: 1 receptacle
120V GFI Duplex: 2 receptacles

Capacities

Fuel Tank: 57 gallons
Run Time: 120 hr full load, 140 hr RCM-D only
Coolant: 4.5 qt.
Engine oil: 3.5 qt.

Size and Weight

Dimensions: 114 inches (length) x 65 inches (width) x 68 inches (height)
Dry Weight: 1265 lbs.
Shipping Weight: 1450 lbs.

Environmental Specifications

Operating temperature: -40° F to 116° F
Operating humidity: 0 to 100%
Maximum Wind Load: 50 mph

Optional Equipment

2 ½” Pintle Hitch
Combination 2” Ball and 2 ½” Pintle Hitch
Rear Ball Hitch
Protective Cover
Gel Cell Battery
Electronic voltage regulator